lone-componenthigh thixotropic silica gel, this product has good adhesion and moderatestrength;
lit can be used alone or in combination with fluorescent powder for strippackaging, and will not collapse after high temperature at high temperature;
lstable opticalperformance and low light decay, improving light efficiency;
lafter curing, it can pass aging test such as cold and heat cycle impact,reflow soldering test, uv test;
l various three-dimensional shapes can be drawnby the dispenser to obtain various illumination angles, which are often usedfor the packaging of rigid led filament bulbs.
inspecting item
|
unit / test method
|
numerical value
|
surface
|
——
|
translucent colloid
|
dynamic viscosity
|
mpa·s/(25℃,10rpm)
|
30-50
|
tectonic viscosity ratio
|
/(3rpm/30rpm)
|
>3
|
condition of cure
|
℃/h
|
170℃/4h
|
gel time
|
sec./(150℃)
|
15
|
operating time at room temperature
|
hrs./(25℃)
|
24
|
storage time
|
months./(-10℃-10℃)
|
3
|
refractive index
|
/(25℃)
|
1.41
|
density
|
g/cm3
|
1.05
|
hardness
|
shore a
|
50
|
shear strength
|
mpa
|
>3
|
tensile strength
|
mpa
|
>4
|
mass resistivity
|
ω·cm/(25℃)
|
>1015
|
coefficient of linear expansion
|
ppm/℃(α2)
|
21
|
lone-componenthigh thixotropic silica gel, this product has good adhesion and moderatestrength;
lit can be usedalone or in combination with fluorescent powder for strip packaging, and willnot collapse after high temperature at high temperature;
lstable opticalperformance and low light decay, improving light efficiency;
lafter curing,it can pass aging test such as cold and heat cycle impact, reflow solderingtest, uv test;
lvariousthree-dimensional shapes can be drawn by the dispenser to obtain variousillumination angles, which are often used for the packaging of rigid ledfilament bulbs.
inspecting item
|
unit / test method
|
numerical value
|
surface
|
——
|
translucent colloid
|
dynamic viscosity
|
mpa·s/(25℃,10rpm)
|
25-35
|
tectonic viscosity ratio
|
/(3rpm/30rpm)
|
>3
|
condition of cure
|
℃/h
|
170℃/4h
|
gel time
|
sec./(150℃)
|
15
|
operating time at room temperature
|
hrs./(25℃)
|
24
|
storage time
|
months./(-10℃-10℃)
|
3
|
refractive index
|
/(25℃)
|
1.41
|
density
|
g/cm3
|
1.05
|
hardness
|
shore a
|
50
|
shear strength
|
mpa
|
>3
|
tensile strength
|
mpa
|
>4
|
mass resistivity
|
ω·cm/(25℃)
|
>1015
|
coefficient of linear expansion
|
ppm/℃(α2)
|
210
|
l two-componenthigh thixotropic silicone, this product has good adhesion and moderate strength;
l it can be usedalone or in combination with fluorescent powder for strip packaging, and willnot collapse after high temperature at high temperature;
l stable opticalperformance and low light decay, improving light efficiency;
l after curing,it can pass aging test such as cold and heat cycle impact, reflow solderingtest, uv test;
l variousthree-dimensional shapes can be drawn by the dispenser to obtain variousillumination angles, which are often used for the packaging of rigid ledfilament bulbs.
inspecting item
|
unit / test method
|
numerical value
|
surface
|
——
|
agent a translucent colloid b clear liquid.
|
dynamic viscosity
|
mpa·s/(25℃,10rpm)
|
30-50
|
tectonic viscosity ratio
|
/(3rpm/30rpm)
|
>3
|
condition of cure
|
℃/h
|
170℃/4h
|
gel time
|
sec./(150℃)
|
15
|
operating time at room temperature
|
hrs./(25℃)
|
24
|
storage time
|
months./(-10℃-10℃)
|
6
|
refractive index
|
/(25℃)
|
1.41
|
density
|
g/cm3
|
1.05
|
hardness
|
shore a
|
50-55
|
light transmittance
|
-
|
>85%
|
tensile strength
|
mpa
|
>4
|
mass resistivity
|
ω·cm/(25℃)
|
>1015
|
coefficient of linear expansion
|
ppm/℃(α2)
|
210
|
ltwo-componenthigh thixotropic silicone, this product has good adhesion and moderate strength;
lit can be usedalone or in combination with fluorescent powder for strip packaging, and willnot collapse after high temperature at high temperature;
lstable opticalperformance and low light decay, improving light efficiency;
lafter curing,it can pass aging test such as cold and heat cycle impact, reflow solderingtest, uv test;
la variety ofthree-dimensional shapes can be drawn by the dispenser, and variousillumination angles are obtained, which are commonly used for packaging ofhigh-power led filament bulbs of 15 ma or more.
inspecting item
|
unit / test method
|
numerical value
|
surface
|
——
|
agent a translucent colloid b clear liquid.
|
dynamic viscosity
|
mpa·s/(25℃,10rpm)
|
30-50
|
tectonic viscosity ratio
|
/(3rpm/30rpm)
|
>3
|
condition of cure
|
℃/h
|
170℃/4h
|
gel time
|
sec./(150℃)
|
15
|
operating time at room temperature
|
hrs./(25℃)
|
24
|
storage time
|
months./(-10℃-10℃)
|
6
|
refractive index
|
/(25℃)
|
1.41
|
density
|
g/cm3
|
1.05
|
hardness
|
shore a
|
50-55
|
light transmittance
|
-
|
>85%
|
tensile strength
|
mpa
|
>4
|
mass resistivity
|
ω·cm/(25℃)
|
>1015
|
coefficient of linear expansion
|
ppm/℃(α2)
|
210
|
ltwo-component addition molding silicone potting glue, mainly suitablefor integral molding of led point light source;
lmoderateviscosity, good formability, easy to inject
lfast curing, goodadhesion, smooth, full and non-collapse after curing;
lexcellent heat resistance, long-termresistance to high temperatures above 260 °c, no cracking, nohardening and no yellowing.
project
|
technical parameter
|
before curing
(component a)
|
surface
|
translucent liquid
|
dynamic viscosity
mpa·s(25℃)
|
50000 - 60000
|
before curing
(component b)
|
surface
|
transparency liquid
|
dynamic viscosity
mpa·s(25℃)
|
300 - 500
|
usage scale
|
4:1
|
post-mixed viscosity mpa·s(25℃)
|
10000 -15000
|
typical curing conditions
|
150℃×2h
|
after curing
|
surface
|
colorless transparent elastic body
|
hardness(shorea)
|
45 ± 5
|
refractive index (25℃ )
|
1.41
|
light transmittance
(% 、1mm@450nm)
|
>85
|